Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
en:xboot:readme [2012/01/09 07:00] alex [1.1 Compatibility List] |
en:xboot:readme [2012/03/07 04:22] (current) alex [1.1 Compatibility List] |
||
|---|---|---|---|
| Line 36: | Line 36: | ||
| * atxmega256d3 | * atxmega256d3 | ||
| * atxmega16a4u | * atxmega16a4u | ||
| - | * atxmega32a4u | + | * atxmega32a4u * |
| * atxmega64a3u | * atxmega64a3u | ||
| * atxmega64a4u | * atxmega64a4u | ||
| Line 54: | Line 54: | ||
| * atmega3250 | * atmega3250 | ||
| * atmega328p * | * atmega328p * | ||
| + | * atmega329 | ||
| + | * atmega3290 | ||
| + | * atmega64 | ||
| * atmega640 | * atmega640 | ||
| * atmega644 | * atmega644 | ||
| Line 59: | Line 62: | ||
| * atmega645 | * atmega645 | ||
| * atmega6450 | * atmega6450 | ||
| + | * atmega649 | ||
| + | * atmega649p | ||
| + | * atmega6490 | ||
| + | * atmega128 | ||
| * atmega1280 | * atmega1280 | ||
| * atmega1281 | * atmega1281 | ||
| Line 115: | Line 122: | ||
| In many cases, this allows you to use the AVRDude program command without having to manually reset the AVR. Alternatively, the API call ''xboot_reset()'' will have the same effect. | In many cases, this allows you to use the AVRDude program command without having to manually reset the AVR. Alternatively, the API call ''xboot_reset()'' will have the same effect. | ||
| + | |||
| + | === - Combine hex files === | ||
| + | |||
| + | To streamline programming multiple chips for a production run, the tool ''srec_cat'' can be used to combine the hex files. Use the command as follows: | ||
| + | |||
| + | <code> | ||
| + | srec_cat xboot.hex -intel main.hex -intel -o mergedfile.hex -intel | ||
| + | </code> | ||
| + | |||
| + | This will concatenate the two hex files together with the proper offsets. Please make sure to use xboot.hex and not xboot-boot.hex to ensure tha the correct offset is used (xboot.hex is relative to address 0 while xboot-boot.hex is relative to the start of the boot section). Note that the combined hex file cannot be programmed with xboot; it is intended to be written with an ISP programmer so both xboot and the application are written in one step. | ||
| ===== - Configuring XBoot ===== | ===== - Configuring XBoot ===== | ||
| - | XBoot is designed to be reconfigured to suit specific needs. Out of the box, all of the standard features are turned on. Turning off features and reassigning pins is easy, just pick a .conf.mk file in the .conf folder, make a copy of it, and edit the appropriate parameters. Then build xboot with your parameters by running "make [file].conf.mk". | + | XBoot is designed to be reconfigured to suit specific needs. Out of the box, all of the standard features are turned on. Turning off features and reassigning pins is easy, just pick a .conf.mk file in the .conf folder, make a copy of it, and edit the appropriate parameters. Then build xboot with your parameters by running ''make [file].conf.mk''. |
| Recommended configuration: | Recommended configuration: | ||
| Line 229: | Line 246: | ||
| * ''UART_U2X'' turns on the double-rate BRG in ATMEGA parts | * ''UART_U2X'' turns on the double-rate BRG in ATMEGA parts | ||
| * Note: this only applies to ATMEGA devices | * Note: this only applies to ATMEGA devices | ||
| + | * ''UART_RX_PUEN'' enables a pull-up on the UART RX pin | ||
| === - USE_UART_EN_PIN === | === - USE_UART_EN_PIN === | ||